董桂伟｜山东大学｜学者主页

2024

产学研融合的快速热循环注塑虚拟仿真实验教学课程建设与实践

董桂伟，王桂龙，赵国群

《高分子通报》

2024

Significantly enhanced joint strength and fatigue life of aerospace composite joints by using novel PEEK/PPS woven meshes as joining agent

Dong Quan, Long Qin, Han Chen, Jia Liu, Jun Lin, Guiwei Dong, Guoqun Zhao

Thin-Walled Structures

DOI

2024

Super‐Elastic and Dimensionally Stable Polyether Block Amide Foams Fabricated by Microcellular Foaming with CO2&N2 as Co‐Blowing Agents

Haoqing Yang, Guiwei Dong, Guilong Wang, Jinchuan Zhao, Guoqun Zhao

Macromolecular Materials and Engineering

DOI

2023

Carbon fibre composite joints co-cured by advanced PEEK/PPS meshes with outstanding fracture toughness

Dong Quan, Han Chen, Long Qin, Jun Lin, Guiwei Dong, Guoqun Zhao

Composites Science and Technology

DOI

2023

Combined effects of nanoparticle and stretch‐induced orientation on crystal structure and properties of UHMWPE / TiO2 composite microporous membranes

Tao Hu, Yue Mu, Yunqiang Chen, Chengfan Zhou, Guoqun Zhao, Guiwei Dong

Polymer Composites

DOI

2022

Lightweight, low-shrinkage and high elastic poly(butylene adipate-co-terephthalate) foams achieved by microcellular foaming using N2 & CO2 as co-blowing agents

Zhaozhi Wang, Jinchuan Zhao, Guilong Wang, Zhaorui Xu, Aimin Zhang, Guiwei Dong, Guoqun Zhao

Journal of CO2 Utilization

DOI

2022

Microcellular injection molded lightweight and tough poly (L-lactic acid)/in-situ polytetrafluoroethylene nanocomposite foams with enhanced surface quality and thermally-insulating performance

Jialong Chai, Guilong Wang, Aimin Zhang, Guiwei Dong, Shuai Li, Jinchuan Zhao, Guoqun Zhao

International Journal of Biological Macromolecules

DOI

2022

Anti-shrinkage, high-elastic, and strong thermoplastic polyester elastomer foams fabricated by microcellular foaming with CO2 & N2 as blowing agents

Zhaorui Xu, Guilong Wang, Jinchuan Zhao, Aimin Zhang, Guiwei Dong, Guoqun Zhao

Journal of CO2 Utilization

DOI

2022

Miscible polymethyl methacrylate/polylactide blend with enhanced foaming behavior and foam mechanical properties

Jinchuan Zhao, Chao Wei, Guilong Wang, Shuai Li, Aimin Zhang, Guiwei Dong, Guoqun Zhao

Journal of CO2 Utilization

DOI

2022

Ultra-light, super-insulating, and strong polystyrene/carbon nanofiber nanocomposite foams fabricated by microcellular foaming

Jinchuan Zhao, Guilong Wang, Weijun Zhu, Zhaorui Xu, Aimin Zhang, Guiwei Dong, Guoqun Zhao

European Polymer Journal

DOI

2022

Lightweight and strong polypropylene/talc/polytetrafluoroethylene foams with enhanced flame-retardant performance fabricated by microcellular foam injection foaming

Jinchuan Zhao, Guilong Wang, Weijun Zhu, Hongfu Zhou, Yunxuan Weng, Aimin Zhang, Guiwei Dong, Guoqun Zhao

Materials & Design

DOI

2022

Ultra-elastic and super-insulating biomass PEBA nanoporous foams achieved by combining in-situ fibrillation with microcellular foaming

Jinchuan Zhao, Guilong Wang, Zhaorui Xu, Aimin Zhang, Guiwei Dong, Guoqun Zhao, Chul B. Park

Journal of CO2 Utilization

DOI

2021

Research on cellular morphology and mechanical properties of microcellular injection–molded BCPP and its blends

Jiachang Wang, Guilong Wang, Jinchuan Zhao, Aimin Zhang, Guiwei Dong, Xiebin Wang, Guoqun Zhao, Chul B. Park

The International Journal of Advanced Manufacturing Technology

DOI

2020

变模温与型腔气体反压辅助微孔发泡注塑技术及其产品内外泡孔结构演变

董桂伟，赵国群，李帅，王桂龙，张磊，侯俊吉

《高分子材料科学与工程》

DOI

2020

产学研协同的塑料改性、加工与性能测试一体化综合实验设计与实践

董桂伟，赵国群，王桂龙，宋立彬，王家昌

《实验室研究与探索》

2020

Foaming Behavior Control and Cell Structure Modification of Microcellular Injection Molded Parts by High Pressure Packing and Mold Opening

Guiwei Dong, Zhao Guo-qun, Huan Wu, WANG Guilong

Journal of Mechanical Engineering

DOI

2019

Effects of dynamic mold temperature control on melt pressure, cellular structure, and mechanical properties of microcellular injection-molded parts: An experimental study

Guiwei Dong, Guoqun Zhao, Junji Hou, Guilong Wang, Yue Mu

Cellular Polymers

DOI

2018

超临界流体辅助微孔发泡注塑技术及其熔体发泡行为

董桂伟，赵国群，管延锦，王桂龙，侯俊吉，吴昊

《机械工程学报》

2018

Ultra-high expansion linear polypropylene foams prepared in a semi-molten state under supercritical CO2

Junji Hou, Guoqun Zhao, Guilong Wang, Lei Zhang, Guiwei Dong, Bo Li

The Journal of Supercritical Fluids

DOI

2018

Lightweight and strong microcellular injection molded PP/talc nanocomposite

Guilong Wang, Guoqun Zhao, Guiwei Dong, Yue Mu, Chul B. Park

Composites Science and Technology

DOI

2018

Lightweight, super-elastic, and thermal-sound insulation bio-based PEBA foams fabricated by high-pressure foam injection molding with mold-opening

Guilong Wang, Guilong Wang, Guoqun Zhao, Guiwei Dong, Yue Mu, Chul B. Park, Guizhen Wang, Guizhen Wang

European Polymer Journal

DOI

2018

Foaming Mechanism of Polypropylene in Gas-Assisted Microcellular Injection Molding

Junji Hou, Guoqun Zhao, Lei Zhang, Guiwei Dong, Guilong Wang

Industrial & Engineering Chemistry Research

DOI

2018

Lightweight, thermally insulating, and low dielectric microcellular high-impact polystyrene (HIPS) foams fabricated by high-pressure foam injection molding with mold opening

Guilong Wang, Guoqun Zhao, Guiwei Dong, Libin Song, Chul B. Park

Journal of Materials Chemistry C

DOI

2018

Supercritical Fluid Assisted Microcellular Injection Molding and the Melt Foaming Behaviors

Gui-Wei Dong

DOI

2017

Morphology Evolution and Elimination Mechanism of Bubble Marks on Surface of Microcellular Injection-Molded Parts with Dynamic Mold Temperature Control

Guiwei Dong, Guoqun Zhao, Lei Zhang, Junji Hou, Bo Li, Guilong Wang

Industrial & Engineering Chemistry Research

DOI

2017

A novel gas-assisted microcellular injection molding method for preparing lightweight foams with superior surface appearance and enhanced mechanical performance

Junji Hou, Guoqun Zhao, Guilong Wang, Guiwei Dong, Jiaju Xu

Materials & Design

DOI

2016

Investigation on bubble morphological evolution and plastic part surface quality of microcellular injection molding process based on a multiphase-solid coupled heat transfer model

Lei Zhang, Guoqun Zhao, Guilong Wang, Guiwei Dong, Hao Wu

International Journal of Heat and Mass Transfer

DOI

2015

微孔发泡注塑成型技术及其产品泡孔结构形成过程和演变规律研究

董桂伟

《山东大学》

2015

Study on reducing sink mark depth of a microcellular injection molded part with many reinforcing ribs

Shuai Li, Guoqun Zhao, Guiwei Dong, Jiachang Wang

Journal of Cellular Plastics

DOI

2015

Formation mechanism and structural characteristics of unfoamed skin layer in microcellular injection-molded parts

Guiwei Dong, Guoqun Zhao, Yanjin Guan, Shuai Li, Xiaoxin Wang

Journal of Cellular Plastics

DOI

2015

Bubble morphological evolution and surface defect formation mechanism in the microcellular foam injection molding process

Lei Zhang, Guoqun Zhao, Guiwei Dong, Shuai Li, Guilong Wang

RSC Advances

DOI

2014

Finite element simulation of three-dimensional viscoelastic planar contraction flow with multi-mode FENE-P constitutive model

Yue Mu, Guoqun Zhao, Anbiao Chen, Guiwei Dong, Shuai Li

Polymer Bulletin

DOI

2014

The cell forming process of microcellular injection‐molded parts

Guiwei Dong, Guoqun Zhao, Yanjin Guan, Guilong Wang, Xiaoxin Wang

Journal of Applied Polymer Science

DOI

2014

Numerical investigation of the crystallization and orientation behavior in polymer processing with a two-phase model

Yue Mu, Guoqun Zhao, Anbiao Chen, Guiwei Dong, Shuai Li

Computers & Chemical Engineering

DOI

2013

Numerical investigation of viscoelastic flow induced crystallization in polymer processing

Yue Mu, Guoqun Zhao, Xiànghóng Wú, Guiwei Dong

AIP conference proceedings

DOI

2006

Bearing Land Entity Information Organizing of Aluminum Profile Extrusion Die CAD System

Guiwei Dong

Modern Manufacturing Technology and Equipment

2006

Research on the Relationship between Die Shape of Drawing Parts and Drawbead Installation by Numerical Simulation

Guiwei Dong

China Metal Forming Equipment & Manufacturing Technology

精选作品

期刊论文

产学研融合的快速热循环注塑虚拟仿真实验教学课程建设与实践

Significantly enhanced joint strength and fatigue life of aerospace composite joints by using novel PEEK/PPS woven meshes as joining agent

Super‐Elastic and Dimensionally Stable Polyether Block Amide Foams Fabricated by Microcellular Foaming with CO2&N2 as Co‐Blowing Agents

Carbon fibre composite joints co-cured by advanced PEEK/PPS meshes with outstanding fracture toughness

Combined effects of nanoparticle and stretch‐induced orientation on crystal structure and properties of UHMWPE / TiO2 composite microporous membranes

Lightweight, low-shrinkage and high elastic poly(butylene adipate-co-terephthalate) foams achieved by microcellular foaming using N2 & CO2 as co-blowing agents

Microcellular injection molded lightweight and tough poly (L-lactic acid)/in-situ polytetrafluoroethylene nanocomposite foams with enhanced surface quality and thermally-insulating performance

Anti-shrinkage, high-elastic, and strong thermoplastic polyester elastomer foams fabricated by microcellular foaming with CO2 & N2 as blowing agents

Miscible polymethyl methacrylate/polylactide blend with enhanced foaming behavior and foam mechanical properties

Ultra-light, super-insulating, and strong polystyrene/carbon nanofiber nanocomposite foams fabricated by microcellular foaming

Lightweight and strong polypropylene/talc/polytetrafluoroethylene foams with enhanced flame-retardant performance fabricated by microcellular foam injection foaming

Ultra-elastic and super-insulating biomass PEBA nanoporous foams achieved by combining in-situ fibrillation with microcellular foaming

Research on cellular morphology and mechanical properties of microcellular injection–molded BCPP and its blends

变模温与型腔气体反压辅助微孔发泡注塑技术及其产品内外泡孔结构演变

产学研协同的塑料改性、加工与性能测试一体化综合实验设计与实践

Foaming Behavior Control and Cell Structure Modification of Microcellular Injection Molded Parts by High Pressure Packing and Mold Opening

Effects of dynamic mold temperature control on melt pressure, cellular structure, and mechanical properties of microcellular injection-molded parts: An experimental study

超临界流体辅助微孔发泡注塑技术及其熔体发泡行为

Ultra-high expansion linear polypropylene foams prepared in a semi-molten state under supercritical CO2

Lightweight and strong microcellular injection molded PP/talc nanocomposite

Lightweight, super-elastic, and thermal-sound insulation bio-based PEBA foams fabricated by high-pressure foam injection molding with mold-opening

Foaming Mechanism of Polypropylene in Gas-Assisted Microcellular Injection Molding

Lightweight, thermally insulating, and low dielectric microcellular high-impact polystyrene (HIPS) foams fabricated by high-pressure foam injection molding with mold opening

Supercritical Fluid Assisted Microcellular Injection Molding and the Melt Foaming Behaviors

Morphology Evolution and Elimination Mechanism of Bubble Marks on Surface of Microcellular Injection-Molded Parts with Dynamic Mold Temperature Control

A novel gas-assisted microcellular injection molding method for preparing lightweight foams with superior surface appearance and enhanced mechanical performance

Investigation on bubble morphological evolution and plastic part surface quality of microcellular injection molding process based on a multiphase-solid coupled heat transfer model

微孔发泡注塑成型技术及其产品泡孔结构形成过程和演变规律研究

Study on reducing sink mark depth of a microcellular injection molded part with many reinforcing ribs

Formation mechanism and structural characteristics of unfoamed skin layer in microcellular injection-molded parts

Bubble morphological evolution and surface defect formation mechanism in the microcellular foam injection molding process

Finite element simulation of three-dimensional viscoelastic planar contraction flow with multi-mode FENE-P constitutive model

The cell forming process of microcellular injection‐molded parts

Numerical investigation of the crystallization and orientation behavior in polymer processing with a two-phase model

Numerical investigation of viscoelastic flow induced crystallization in polymer processing

Bearing Land Entity Information Organizing of Aluminum Profile Extrusion Die CAD System

Research on the Relationship between Die Shape of Drawing Parts and Drawbead Installation by Numerical Simulation

预印本

Enhanced Foaming Behavior and Foam Mechanical Properties of Pmma by Compounding with Miscible Pla

研究方向